TC Generator & start TC
LTCast has two timecode sources, chosen with the two tabs above the big timecode display:
- LTC Reader — the timecode comes from the LTC channel of the song's audio file. The badge shows SIGNAL OK (with the detection confidence and the channel) or NO SIGNAL.
- TC Generator — LTCast makes the timecode itself from the playhead position and the song's Start TC. The badge reads GENERATING, or a grey GENERATOR PAUSED while chase is following external timecode and nothing is playing, because the generator is not sending LTC then. Use it for a song with no LTC of its own, or when you want to set the timecode address yourself.
The generated timecode drives the big display and every output, including an encoded LTC signal on the LTC output device. The TC Generator is a Pro feature (a Pro licence or an active trial): without Pro LTCast holds it off and shows a message instead of generating timecode.
Start TC — per song
In TC Generator mode the controls under the display show Start TC: the timecode at which the song starts. It belongs to one song — the song you have preselected (STANDBY) or, failing that, the active song — and there is no global start timecode. It shows 00:00:00:00 until you set it. Click the field and type HH:MM:SS:FF, or eight digits such as 01000000, and press Enter. A common convention is one hour per song (01:00:00:00, 02:00:00:00, …).
If the song already has triggers when you change its Start TC, LTCast asks what to do: Move the triggers too shifts them by the same amount (right when you are moving the whole show to another hour), or Keep their timecodes leaves them where they are (right when you are correcting a start TC that was typed wrongly).
Set start TCs in order
To give a whole setlist its Start TCs at once, click ⋯ in the setlist header (tooltip: More setlist actions) and choose Set start TCs in order. It is for songs with no LTC in the file, so chase can find them. The item is greyed out while the setlist is empty or Chase is locked to an external signal.
Set where the first song starts in Start at (01:00:00:00 until you change it), and choose how the rest follow, at the frame rate set for the TC Generator. Empty Songs are laid out with the others.
- Each on the hour: the default. Each song starts one hour after the song above it.
- End to end: each song starts where the song above it ends, rounded up to a whole frame so two songs do not overlap.
The dialog lists every song with its new Start TC before anything changes. A song that will stay as it is shows the reason instead:
- Has LTC, unchanged: the file carries LTC, and chase reads that. The song still counts, so the song after it starts an hour later or after its length.
- Length unknown: End to end only. LTCast could not read the song's length, so it cannot place that song or any song without LTC after it.
- Past 24 hours: the song would go past the end of the 24-hour timecode.
Click Apply to set them, or Cancel to change nothing. Apply is greyed out if no song would change or Start at is not a valid timecode (Enter a timecode like 01:00:00:00.). LTCast saves an automatic snapshot first. If songs that moved have triggers, it asks once for all of them: Move the triggers too or Keep their timecodes.
Frame rate
The Frame Rate buttons — 23.976, 24, 25, 29.97 (drop-frame) and 30 — set the generator's rate; the grey chip beside the TIMECODE label shows it. In LTC Reader mode the same chip is the control: click it and choose Auto, 24, 25, 29.97 or 30 to override the rate read from the file; it is disabled while chasing. While a song plays, the Start TC field, the Frame Rate buttons, the chip and the two tabs are held (hover for why); a Lite show has no TC Generator tab.
Pre-roll
Pre-roll runs the timecode for a few seconds before the music starts, so a console has time to lock and you have room for a pre-cue. In TC Generator mode a Pre-roll box is behind the small ... button in the transport bar (together with Offset and Loop; when it is not zero an amber Pre-roll 4s chip stays in the bar and opens it), with − and + buttons and the unit s. It is set per song, from 0 to 60 seconds, and it lights up when it is not zero. Right-click the box to reset it to 0.
When you press Play, the timecode starts at the Start TC minus the pre-roll and counts up while the music is silent; the box shows a countdown; and the music enters exactly on the Start TC. Cues and triggers are unaffected, because the music still lands on the timecode you set. Two limits apply:
- The pre-roll cannot be longer than the Start TC itself, because timecode cannot go below zero. With a Start TC of
00:00:00:00the box is disabled — set a later Start TC first. - It happens only when you press Play. Seeking, resuming from a pause and auto-advancing to the next song never run it again.
The guide has the same steps with screenshots.
A song with no LTC in its file is followed by chase through the Start TC set here and its length — the same timecode the generator plays it at, so a show generated on one computer lines up when chased on another. The TC Generator creates timecode for LTCast's own outputs; it does not add LTC to the song file.