Outputs
Settings → Outputs holds the behavior of everything LTCast sends, plus a few playback controls that belong with it. Choosing the audio and MIDI devices is in Settings → Devices. This is the order of the rows.
Pro. MTC, Art-Net and OSC timecode — and generated LTC — are sent only while the session is Pro (a Pro licence or an active trial). Without Pro nothing is sent: the lights for outputs that are switched on turn amber and read Needs Pro, and Pre-Show Check warns about it. The file's own LTC, MIDI Clock, DIM, the Esc fade and the scrub speed are not affected. A session that has been Pro since it started stays Pro until you quit, so a licence problem in the middle of a show does not cut the outputs.
LTC level
LTC Level — the level of the LTC signal, from silence up to +3.5 dB; 0 dB leaves it unchanged. Right-click or double-click the slider to reset it to 0 dB. The hint recommends −3 to 0 dB for Resolume Arena; reduce it only if the receiving device clips or rejects the signal.
Esc fade-out
Off by default. When on, Esc fades the music out over the Fade time (0.2 to 10 seconds, default 1.2) before stopping; a second Esc during the fade cuts immediately. The Stop button always stops at once. The fade moves the music only: the LTC stays at full level during the fade and goes silent when the song stops. See ESC fade-out.
Arrow-key scrub speed
How fast the playhead moves while you hold → or ← to skip to a point in rehearsal: 1.25×, 1.5×, 2× (default), 3× or 5×. Fast-forward up to 2× is audible; 3× and 5× skip silently, and rewinding is always silent. Outputs and triggers are held while you scrub and re-aligned when you release. It is disabled while chasing.
Talk-over DIM
Chooses how DIM ducks the music for an announcement: Hold (momentary) — the music is ducked while you hold the DIM button or the D key and returns when you release — or Toggle (latch), where each press switches ducking on or off. The default is Hold. Duck level sets how far the music drops, from −60 to 0 dB (default −15 dB). See DIM.
MTC
MTC Mode — Quarter-frame (recommended), the continuous stream (4 messages per frame), or Full-frame (legacy), which sends one SysEx message every time the frame number changes — not only when you locate or stop — for older devices that cannot read quarter-frame. See MTC Output.
MIDI Clock
MIDI Clock Output — tick to send 24 PPQ clock on the MTC port (enabled once a port is selected). BPM Source is Auto Detect (a live estimate that can change during a song), Tap Tempo (the value you tapped with TAP), or Manual (a fixed BPM from 20 to 300). See MIDI Clock Output.
Trigger MIDI port
Trigger MIDI port — where MIDI triggers (program change, note, control change and MSC) are sent. It is separate from the MTC port, and OSC triggers use the OSC targets below instead.
Art-Net TC
Tick Art-Net TC to send OpTimeCode on UDP port 6454. Under it is the target list — an enable checkbox and an IP address per row, + Add target to add one. A new target starts as 255.255.255.255. See Art-Net (OpTimeCode).
OSC Output
Tick OSC Output to send OSC. Each row of the target list has an enable checkbox, an IP address, a port and a template: Generic (/timecode), Resolume Arena, Disguise (d3) or WATCHOUT. Generic sends /timecode with five integers (hours, minutes, seconds, frames, fps); the other three send a HH:MM:SS:FF string and a float frame rate to their own address. A new target starts as 127.0.0.1 port 8000. See OSC Output.
TC Feedback (Inbound)
The listener for OSC acknowledgements from receivers: a toggle, a Port (default 9001) and a Bind choice of local only or LAN. It is off at every launch. See OSC feedback.
Resolume Arena
At the bottom, the link that fires Arena columns and clips by Arena's own ID and records what you hit in Arena: Connect to Resolume Arena (off by default), Address (default 127.0.0.1), Port (default 8080) and a line that says what the connection is doing. It is a Pro feature. See Resolume Arena link.